Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Irving?
Chimney cap installation in Irving typically costs $150 to $450, and crown repair or replacement typically runs $300 to $900, depending on the size and condition of the masonry. Most Irving homeowners spend somewhere between $200 and $500 for a stock cap on a standard single-flue chimney, while a full crown rebuild with proper slope and bonding lands closer to the top of that range.
Crown and cap work rarely travels alone. A cap that’s failed usually means water has been getting to the crown, and a cracked crown often shows up alongside spalling brick or a damaged flue. That’s why we quote the whole job after looking at the whole system, and the written estimate is what sets your final price.
Key Takeaways
- Stock caps: $150-$450. Custom or multi-flue caps: $450-$900+.
- Crown repair (sealing or patching): $300-$600. Full crown reconstruction: $600-$900.
- In Irving, wind-driven rain and DFW hail do more crown damage than cold weather does.
- A failed cap lets water in; a failed crown lets water into the masonry itself. Both get worse and more expensive if ignored.
- Free estimates, upfront pricing, and technicians with up to experience on the work.
Chimney Cap & Crown Cost Breakdown (2026)
Here’s how the numbers break out for the Irving market. These are typical estimated ranges for the work itself, materials included. The written estimate sets the final price.
| Item | Typical Estimated Range | What It Covers |
|---|---|---|
| Stock single-flue cap | $150-$450 | Standard stainless or galvanized cap sized to your flue, installed with a proper mounting system |
| Custom or multi-flue cap | $450-$900+ | Fabricated cap for odd flue sizes, multiple flues, or stone and stucco chimneys |
| Crown sealing or patching | $300-$600 | Hairline cracks and minor erosion treated and resealed |
| Full crown reconstruction | $600-$900 | Old crown removed, new crown formed with the correct slope, bonded and cured |
| Crown wash and bond repair | $200-$400 | Overhanging crown edge rebuilt where it’s separated from the brick |
| Cap + crown together | $450-$1,300 | Combined job, which is how most homeowners actually book it |
| Liner inspection add-on | Priced with the visit | Checking the flue while we’re on the roof, since crown leaks often reach the liner |
The range moves up for taller or steeper roofs, stone or stucco chase covers that need custom fitment, multiple flues, or a crown that’s so far gone the whole thing comes off. It moves down when a cap only needs reseating and the crown is sound. Copper caps sit at the top of the cap range because the material costs more and the fabrication is custom; Gelco and Famco units are the workhorses for standard residential flues, and we size them to the actual flue opening rather than the nearest box on a shelf.
One thing worth saying plainly: the cap-and-crown line item is often the cheapest part of a bigger repair. If water has been reaching the flue for a while, the liner may show damage too, and that’s a separate quote. We’d rather tell you the whole picture upfront than hand you a surprise later.
What Affects Chimney Cap & Crown Pricing in Irving
- Roof pitch and access. A steep roof or a chimney set well back from the ridge takes longer to work on safely, and that time is part of the estimate. Irving’s mix of one-story ranch homes and newer two-story builds in the Las Colinas and Valley Ranch areas both come up, and the two rarely price the same.
- Chimney material. Brick is straightforward. Stucco and stone chases often need custom cap fabrication because nothing off the shelf fits, and that pushes the cap toward the custom range.
- Number of flues. A single flue takes a single cap. A chimney serving a fireplace plus a furnace or water heater flue needs a multi-flue cap, which is more material and more mounting work.
- How far the crown has deteriorated. Sealing hairline cracks is one job. Rebuilding a crown that’s separated from the brick and shedding water into the masonry is another, and the price reflects which one you actually need.
- Weather timing. Crown work needs reasonable conditions to bond and cure. Irving’s spring storm season and the summer heat both affect scheduling, and a job that can wait for a clear window is easier to plan than one that can’t.
- Whether the liner is involved. A cracked crown lets water run down the inside of the chimney. If that water has reached the flue, you’re looking at a liner assessment in addition to the crown work. We check this before quoting so there are no surprises.
Why Caps and Crowns Matter More in Irving Than You’d Think
Irving doesn’t have harsh winters. What it has is wind-driven rain, hail, and long stretches of heat. Those are the conditions that age a chimney crown. A crown is a concrete cap that sits on top of the masonry and slopes water away from the brick. When the slope goes flat or a crack opens up, water gets into the brick and the flue instead of running off. Over a few seasons that shows up as spalling brick, rusted damper components, and a liner that’s taken on moisture.
The cap does a different job. It keeps rain, birds, and debris out of the flue opening. A missing or rusted-out cap is one of the most common things we find on Irving roofs, and it’s one of the cheapest things to fix before it turns into something bigger. A clean chimney is the starting point. A capped and properly crowned one stays that way.
This is also where working with professional-grade materials matters. We work with DuraFlex and HeatShield, the same brands chimney specialists trust for liner and resurfacing work, and we size caps from Gelco, Famco, Olympia Chimney, and Copperfield to fit the actual flue. If the crown job turns out to involve the liner, we can handle that too rather than handing you off to someone else.
What Does a Chimney Cap Actually Do, and Do You Need One in Irving?
Yes, you need one. A chimney cap keeps rain out of the flue, stops birds and squirrels from nesting in it, and catches sparks before they reach the roof. Without a cap, an Irving chimney takes on water every time it rains, and that water goes straight down the flue to the damper and firebox.
Most caps we see fail in one of two ways: the mounting legs rust through and the cap sits loose, or the mesh screen tears and stops doing its job. Either way, the fix is usually a replacement rather than a repair, and the price band is the same $150-$450 you see in the table above. Call (855) 955-5057 for a free estimate. We answer 24/7.
How Much Does Crown Repair Cost in Irving, and Can It Wait?
Crown repair in Irving typically costs $300 to $600 for sealing and patching, and $600 to $900 for a full reconstruction. It can wait a short while if the damage is hairline cracks, but it shouldn’t wait through a rainy season. Every storm that hits an open crack pushes more water into the masonry, and masonry that stays wet is masonry that spalls.
If you’re seeing missing chunks of concrete on the roof or a crown that’s pulling away from the brick, that’s the point to get it looked at. Call (855) 955-5057 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
How to Save on Chimney Cap & Crown
There are a few practical ways to keep this work from costing more than it should.
- Book the cap and crown together. Both jobs happen on the same roof visit, and a combined estimate is almost always less than two separate appointments.
- Catch the crown early. Sealing hairline cracks at the $300-$600 level is far cheaper than a full reconstruction at $600-$900, and much cheaper than repairing water-damaged masonry afterward.
- Get the full chimney looked at while we’re up there. A crown inspection and a sweep on the same visit means one trip, one estimate, and no gap between the person who finds a problem and the person who fixes it.
- Ask about the liner. If water has been getting in, knowing whether the flue is sound now saves you from paying for a second visit later. Our Irving Chimney Cleaning team handles sweep, repair, and inspection as one integrated service, so nothing gets missed between them.
- Get a written estimate before work starts. Estimates are free and the price is set per job by that written estimate, so you know the number before anyone gets on the roof.
For Irving homeowners planning ahead, the best window for crown work is a dry stretch outside the peak of storm season. Schedule your inspection before the burning season so repairs don’t become emergencies. Call (855) 955-5057 for a free estimate. We answer 24/7.
Can You Fix a Chimney Cap the Same Day?
Often, yes. A stock cap replacement on a standard single-flue chimney is usually a same-day job once we’ve seen the flue size and mounting setup. Custom or multi-flue caps take longer because they’re fabricated to fit, and a full crown reconstruction needs cure time on top of the install. Call (855) 955-5057 for a free estimate and we’ll tell you what your chimney needs. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Is It Cheaper to Repair a Crown or Replace It?
Repair is cheaper when the damage is surface-level: hairline cracks and minor erosion usually fall in the $300-$600 range, while full replacement runs $600-$900. The deciding factor is whether the crown still has its slope and is still bonded to the brick. A crown that’s flat, separated, or crumbling across the whole top needs replacing, because patching it just delays the same problem. We’ll show you what we’re seeing and quote the option that actually fixes it. Call (855) 955-5057 for a free estimate – estimates are free and the written quote sets the final price.
FAQs – Chimney Cap & Crown Cost
How much does a chimney cap cost in Irving?
A stock single-flue chimney cap in Irving typically costs $150-$450 installed, and custom or multi-flue caps run $450-$900+. The written estimate sets the final price. Call (855) 955-5057 for a free estimate. We answer 24/7.
How much does chimney crown repair cost in Irving?
Crown repair in Irving typically costs $300-$600 for sealing and patching, or $600-$900 for a full reconstruction. Call (855) 955-5057 for a free estimate – estimates are free and the price is set per job by the written estimate.
Do I really need a chimney cap in Irving?
Yes. A cap keeps rain, birds, and debris out of the flue, and without one an Irving chimney takes on water every storm. A replacement cap typically runs $150-$450 installed. Call (855) 955-5057 for a free estimate.
Can you install a chimney cap and repair the crown in one visit?
Usually, yes. Cap and crown work happen on the same roof visit, and a combined estimate typically runs $450-$1,300 depending on the cap and the extent of the crown damage. Call (855) 955-5057 for a free estimate. We answer 24/7.
How do I know if my crown needs repair or full replacement?
Hairline cracks and minor erosion usually mean repair at $300-$600; a flat, separated, or crumbling crown means replacement at $600-$900. We’ll document what we find on the roof and quote the option that actually fixes it. Call (855) 955-5057 for a free estimate.
Get a Free Chimney Cap & Crown Estimate in Irving
Caps and crowns are small line items that protect the whole chimney, and in Irving’s weather they earn their keep. Whether you’re dealing with a rusted-out cap, a crown that’s seen better days, or both, we’ll take a look and give you a written estimate before any work starts. Our technicians have up to experience, and we work with professional-grade brands like Gelco, Famco, Olympia Chimney, and Copperfield so the parts on your chimney are built to last.
If you’re not sure your chimney needs cap or crown work at all, start with an inspection. A documented assessment of chimney condition gives you a clear picture before issues escalate, and it pairs naturally with a sweep if it’s been a while. Our Irving team handles sweep, repair, and inspection as one integrated service, so the company that cleans your chimney can also repair and inspect it. No handoff, no gaps in accountability.
Call (855) 955-5057 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Irving market as of 2026. Irving Chimney Cleaning offers free estimates – call (855) 955-5057.
Written by the team at Irving Chimney Cleaning.
What Our Customers Say
"Level two inspection before we bought the house. The report was detailed enough to use as a negotiating point and he explained every photo in it."
- Bryce Padgett"Creosote buildup was worse than I realized. He measured it, showed me the glazing on the flue with the camera, and was honest that we were closer to a chimney fire than I wanted to hear."
- Renee Hayes"Cap keeps the birds out now, which after two springs of scratching noises is worth every penny."
- Colleen Doyle