Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Irving Homeowners Choose HeatShield Chimney Cleaning
We provide independent HeatShield chimney cleaning, repair, and installation service in Irving, TX. What makes our HeatShield work different is our diagnostic-first approach: we verify the firebox substrate is sound and dry before we ever specify a resurfacing compound, because that judgment, not the brand name on the pail, is what determines whether the repair holds. We’re an independent service provider, not affiliated with or authorized by HeatShield. Our technicians have up to 11 years of experience. Call (855) 955-5057. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Irving Chimney Cleaning for Your HeatShield Chimney Cleaning?
HeatShield work lives or dies on the details most people never see: how the firebox floor was prepped, whether the substrate was properly scored, and how long the material was allowed to cure before the first fire. Our technicians have worked with enough of these systems to know what a correct installation looks like and what a rushed one looks like two winters later. That familiarity is what you’re hiring.
We use quality parts that fit HeatShield equipment when a component needs replacement, and we follow manufacturer-specified cure windows rather than pushing a fireplace back into service because the family wants to burn. Warranty-safe practices matter here: a resurface applied over a wet or sooty surface voids the value of the material regardless of what the label promised, and we won’t take that shortcut.
Irving homes present specific conditions. The 1970s and 1980s masonry fireplaces in south Irving and the builder-grade prefab units common in Valley Ranch and Las Colinas see long idle stretches followed by intense use during ice-storm power outages. That pattern stresses a repaired firebox in ways a fireplace used a few times a month never does. We factor it into every HeatShield evaluation we do in Irving.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common HeatShield Chimney Cleaning Problems We Fix in Irving
- Fireguard 2000 delaminating in sheets. The usual cause is a resurface applied over a damp, sooty, or improperly etched firebox floor. The compound can’t bond to what it can’t grip. When a layer lifts in flat sheets within a season or two, the failure is almost always in the prep, not the product. Correcting it means removing the loose material entirely and starting from a clean, roughened, moisture-tested substrate.
- Cracks tracking along the original mortar joints. A resurfaced firebox that never received a bonding coat or a scored base tends to crack precisely where the old masonry joints sit beneath it. The coating is following the weak lines in the substrate. It looks like a material failure; it’s a base-preparation failure. We grind back to sound brick, score the surface, and bond properly before reapplication.
- Repeat failures caused by water intrusion. This is the one that costs Irving homeowners the most. A HeatShield repair on a firebox with unresolved moisture will fail again and again, because the crown, flashing, or cap was never addressed. The coating becomes a bandage on a leaking system. Every HeatShield job we quote in Irving starts with a look at the chimney top, not just the firebox.
- Skim-coated brick that’s crumbling behind the repair. When spalling depth is misjudged, HeatShield is applied over brick that’s already soft and releasing. The surface looks correct for a while. Then the brick face lets go and takes the coating with it. Probing the brick is not optional, and neither is a straight answer about what we find.
- Firebox floors gone chalky with no prior repair. Uncoated fireboxes exposed to years of heat cycling and occasional moisture can soften across the floor. A homeowner notices the surface dusting away. If the brick beneath is still solid, a properly prepped HeatShield resurface is genuinely the right fix. If the brick is soft through, it isn’t.
HeatShield Parts & Our Repair-vs-Replace Approach
When a HeatShield repair calls for material, we specify Fireguard 2000 or Fireguard 2000 Plus by name because the compound is the reference standard and worth being specific about. But the truth is that success depends far more on surface preparation and cure time than on the brand of trowel. A great product on a bad substrate is a wasted product.
Our repair-vs-replace call comes down to the condition of the brick. If the firebox brick itself is soft, or the firebox is cracked through the wall, honest advice is rebuild or reline rather than a cosmetic resurface. We’ll show you why. We don’t claim to stock OEM or genuine HeatShield parts, and we don’t sell HeatShield products. We repair, install, and service HeatShield systems using quality parts that fit them.
That means we’ll sometimes tell you the HeatShield route isn’t the right spend, and a DuraFlex reline or a firebox rebuild is. We’d rather lose the smaller job than sell you a resurface that fails.
Call (855) 955-5057 for a free estimate on your Irving firebox.
Our HeatShield Service Process – Step by Step
- 1
Diagnosis. We start with a Level 2 inspection of the firebox and the chimney top. That means probing the brick for spalling depth, checking the crown and flashing for water pathways, and confirming whether the existing HeatShield layer is bonded or lifting. You see what we see.
- 2
Repair or install. Water intrusion gets corrected first. Then the firebox is ground back to sound material, scored, bonded, and rebuilt in lifts with HeatShield Fireguard 2000 or Plus, following the material’s specified cure time between applications.
- 3
Test. Once cured, we check the bond across the floor and walls, verify the damper and smoke shelf clear, and confirm the firebox reads dry before we clear the fireplace for use.
- 4
Warranty. We document the repair in writing and walk you through what will keep it sound: crown maintenance, a proper cap, and dry wood. Warranty-safe service means the conditions that caused the original failure don’t get recreated.
See the difference
Before
After
Before
After
Before
AfterHeatShield Products We Service & Install in Irving
We work with the HeatShield resurfacing and repair side of the system, not just a brush-and-vacuum sweep. That includes Fireguard 2000 ceramic refractory resurfacing for firebox floors and walls, and Fireguard 2000 Plus extended-life fireplace resurfacing mortar for fireboxes that see heavier use. We also handle HeatShield fireplace insert surround and baffle repair kits, and HeatShield chimney crown and mortar repair products when the water source needs correcting as part of the job.
We don’t claim to stock these products. We repair, install, and service HeatShield systems using quality parts that fit them, and we specify the right material for what your firebox actually needs. If your Irving chimney has a resurface that’s failing, a crown that’s cracked, or a firebox that was never repaired at all, we’ll tell you where it stands and what the right next step is.
We Also Service These Brands
HeatShield isn’t the only system we work with. Our HeatShield expertise sits alongside DuraFlex liner systems, which we install and service when a firebox or flue needs relining rather than resurfacing, and Gelco products for caps and venting. A full chimney system needs more than one tool. We bring the diagnostic depth to know which one your Irving home actually needs.
FAQs – HeatShield Chimney Cleaning Service in Irving
No. We are an independent HeatShield service provider, not affiliated with or authorized by the manufacturer. That independence means our recommendations are based on your firebox condition, not on brand obligations. Call (855) 955-5057 for an honest assessment.
Yes. When a HeatShield repair needs material, we specify Fireguard 2000 or Plus by name and use quality parts that fit the system. We don’t stock or sell OEM HeatShield products, but we repair, install, and service HeatShield systems with the right materials for the job.
Most HeatShield firebox resurfacing jobs take more than a day, because the material must cure properly between lifts and before the fireplace is used again. Rushing cure time is one of the main reasons HeatShield repairs fail early. We’ll give you a written timeline with your estimate. Call (855) 955-5057 to book an assessment.
We service and install Fireguard 2000 and Fireguard 2000 Plus resurfacing compounds, HeatShield fireplace insert surround and baffle repair kits, and HeatShield chimney crown and mortar repair products. If your firebox needs a different fix entirely, we’ll tell you.
Properly installed HeatShield material applied to a correctly prepped, dry substrate is the warranty-safe path. The failure modes we see most often in Irving, a resurface over a damp or sooty floor, or a repair on a firebox with unresolved water intrusion, are the kinds of shortcuts that undermine the material’s value. We follow prep and cure requirements rather than cutting them. Call (855) 955-5057 to talk through your situation.
HeatShield firebox resurfacing is priced per job by written estimate after we inspect the firebox, because the prep work and cure schedule vary widely. A sweep and Level 2 inspection is a separate, smaller line item. Nothing is quoted until we’ve looked at the substrate and the chimney top. Call (855) 955-5057 for a free estimate, and estimates are free.
No. HeatShield is a firebox resurfacing system, not a flue liner. If your flue itself is damaged or deteriorated, a liner system such as DuraFlex is usually the correct repair, and we can handle that too.
A properly prepped and cured HeatShield resurface holds for years, but the water source must be corrected first. Crown cracks, failed flashing, and missing caps cut that life short fast. Fix the roof-level cause and the firebox repair lasts as it should.
Cracks that follow the original mortar joints usually mean the base was never scored or given a bonding coat before resurfacing. The compound is following weak lines in the substrate beneath it. The fix is to grind back the loose layer and prep and bond the substrate correctly before reapplying.
Yes. A Level 2 inspection is the honest starting point for any HeatShield firebox resurface. It tells us whether the brick is sound enough to resurface or whether a rebuild or reline is the better spend. Without it, a HeatShield quote is a guess. Call (855) 955-5057 to schedule one.
It depends on the insert and how the firebox runs. Some gas fireboxes can take a resurface; others are built for a direct-vent system and shouldn’t be coated. We check the unit and the venting before recommending anything.
Book Your HeatShield Service in Irving, TX
If you’re in Irving and your firebox has a HeatShield layer cracking, lifting, or never applied, call (855) 955-5057. We’re an independent HeatShield service provider, and we’ll give you a straight answer on whether a resurface, a reline, or a rebuild is the right call.
Written by the team at Irving Chimney Cleaning.