Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Irving Homeowners Choose DuraFlex Chimney Cleaning
We provide independent DuraFlex chimney cleaning, inspection, and repair in Irving, TX. That means we service and install the flexible stainless liner systems DuraFlex makes – single-wall relining kits, insulated liner kits, and the caps and top plates that seal them – along with the adapters and hardware that tie the whole assembly to your appliance. What sets our DuraFlex work apart is that we treat the liner as a complete system under real North Texas load, not a single tube that gets brushed once a year. We’re an independent service provider and are not authorized, sponsored, or endorsed by DuraFlex. Our technicians have up to 11 years of experience. Call (855) 955-5057. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Irving Chimney Cleaning for Your DuraFlex Chimney Cleaning?
Our technicians have spent years working on DuraFlex prefab and relined systems, so they know how the stainless liner, the insulation wrap, and the termination hardware actually behave after a few heating seasons in Irving. That matters because a DuraFlex liner fails at its edges and connections far more often than it fails in the middle of a straight run. A sweep who only brushes the flue will miss a rusted top plate or a loosened cap gasket every time.
We use quality parts that fit DuraFlex equipment – stainless liner sections, top plates, caps, and adapters sized to match the assembly. We don’t claim to stock OEM or genuine DuraFlex parts, and we won’t tell you we’re a dealer. What we can tell you is that the parts we install are matched to your system, not adapted to it.
Warranty-safe practice matters here. The common reasons a liner manufacturer declines a claim are aggressive sweeping, a bottom section cut jagged, or a top termination fitted with the wrong size cap. We cut and trim liner ends so the leading edge doesn’t snag a brush, we size terminations to the flue, and we document what we find with a photo report you keep. If your DuraFlex installation has a warranty in place, we work to leave it intact rather than invalidate it with rough handling.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common DuraFlex Chimney Cleaning Problems We Fix in Irving
DuraFlex systems fail in patterns. Here are the ones we run into most in Irving homes.
- Upper-liner corrosion and pinholes from condensate. When a gas or high-efficiency appliance vents through an oversized single-wall DuraFlex liner that was never insulated, the flue gases cool before they leave the top. That produces acidic condensate that eats at the upper liner from the inside out. By the time a homeowner notices, there are often pinholes in the metal that no amount of sweeping cures. Insulation wrap or an insulated liner kit is the real fix when the liner is still sound enough to keep.
- Liner crimp and seam separation from an aggressive sweep. Flexible liner is corrugated stainless, and it doesn’t respond well to a stiff brush run at high speed or a rotary head pushed too hard. Seams open and crimps flatten. An improperly trimmed bottom section leaving a jagged edge makes it worse, because that edge snags the brush and tears at the liner with every pass. We check the bottom transition before we sweep, not after.
- Top-plate and cap hardware loosening or rusting out. The top plate and the cap are the only things keeping North Texas rain out of your flue. Screws back out, gaskets degrade, and steel rusts. Once water gets past either one, it runs down alongside the liner and soaks the insulation wrap, which stops insulating and starts holding moisture against the stainless. You can’t see this from the hearth. You can see it with a camera.
- Liner separation at the appliance connector. Years of thermal cycling – repeated heating and cooling, season after season – work at the connection between the liner and the appliance or the adapter that joins them. A disconnected or compromised adapter lets flue gases escape behind the liner instead of up the flue. That’s a carbon monoxide concern, not a performance quirk, and it needs to be checked at the insert or firebox, not just at the top.
- Deferred sweeping on systems the owner assumed were maintenance-free. Prefab and relined units are often overdue in Irving because owners think a stainless liner means no service. It doesn’t. Creosote still builds in the flue, and a liner doesn’t change that. When North Texas fireplaces sit idle for months and then see heavy use during a winter power outage, the buildup happens in concentrated bursts – exactly the load a neglected DuraFlex system can’t handle safely.
DuraFlex Parts & Our Repair-vs-Replace Approach
DuraFlex-matched stainless liner sections, top plates, caps, and adapters are the right choice for anything load-bearing or exposed to weather. Generic aftermarket caps and clamps have their place, but only for non-structural finishes. We won’t hang the top of your chimney on a part that wasn’t built for it, and the Irwin homeowner deserves a straight answer about which is which.
We don’t claim to stock OEM or genuine DuraFlex parts. We source components that fit DuraFlex equipment properly and install them to spec. When we open up the top of a flue, the decision is usually this: where the liner itself is sound, repair the hardware and the seals – reseat the top plate, replace the cap, restore the adapter. Where the liner is pitted through or has separated, relining is the honest call rather than patching a failing flue. We tell you which is which, show you the camera evidence behind the recommendation, and let you decide.
If you want to know whether your DuraFlex system needs repair or replacement, call (855) 955-5057. Estimates are free.
Our DuraFlex Service Process – Step by Step
- 1
Level 2 inspection. Before anything else, a camera inspection – top down and at the appliance connector – establishes what condition the liner, insulation wrap, top plate, cap, and adapter are actually in. This is the evidence base, and you see it in the photo report.
- 2
Diagnosis. We match the symptoms to the cause. Water stains usually trace to the cap or top plate. Condensate corrosion traces to an uninsulated oversized liner. Escaping gas traces to the adapter. We name the specific part and the specific reason.
- 3
Repair or install. If hardware and seals are the issue, we repair them with DuraFlex-matched parts. If the liner has failed, we install a properly sized liner, with insulation wrap where the appliance and flue call for it, trimming the bottom section clean so nothing snags.
- 4
Test. We verify the draft and the seals, check that the cap and top plate are watertight, and confirm the adapter is connected and sound at the appliance.
- 5
Documentation. You get the photo report of the before and after, the work performed, and the parts used – the record you’d want if a warranty question ever comes up under your DuraFlex installation.
See the difference
Before
After
Before
After
Before
AfterDuraFlex Products We Service & Install in Irving
We service and install the DuraFlex flexible stainless steel liner systems that go into Irving homes – single-wall stainless relining kits, the Pro and ProFlex line of flexible stainless liner kits, insulated liner kits with wrap or an insulation sleeve, and the Pro Rain Caps, Top Plates, and Multi-Flue Caps that terminate them. That covers the full assembly from the appliance connector up through the crown.
We don’t claim to stock these components. We source parts matched to your system and install them as they should be installed. If your system is already relined and you’re not sure what’s up top, a Level 2 inspection answers it. Cap replacement and chimney waterproofing often come up as part of the same visit, since water intrusion at the top plate is the most common thing we find in Irving.
Many Irving masonry chimneys lack a proper cap entirely, which is how chimney swifts and starlings end up nesting in uncapped flues by April. A correctly sized DuraFlex-compatible cap solves that along with the rain.
We Also Service These Brands
We’re not tied to a single product line. Alongside DuraFlex work, we service HeatShield – the specialist interior chimney resurfacing system – and Gelco caps and venting solutions, plus Olympia Chimney, Famco, and Copperfield. That breadth means one company can sweep, diagnose, and repair your whole chimney system without handing you off to someone else. It’s all we do.
FAQs – DuraFlex Chimney Cleaning Service in Irving
No. We are an independent service provider and are not authorized, sponsored, or endorsed by DuraFlex. We work on DuraFlex systems because they’re a professional-grade product line that we know well, not because we’re affiliated with the manufacturer. For a warranty claim under your DuraFlex installation, you’d go to DuraFlex through their channels; we document our work so you have a clear record of what was done.
Yes. We source stainless liner sections, top plates, caps, and adapters that fit DuraFlex equipment properly. We don’t claim to stock OEM or genuine DuraFlex parts, and we’re not a DuraFlex dealer. What we do commit to is that load-bearing and weather-exposed parts are matched to your system rather than fitted with generic substitutes. Call (855) 955-5057 for an exact quote on your DuraFlex service – estimates are free.
Most DuraFlex sweeps and Level 2 inspections are done in a single visit. Repairs and relining take longer, and how long depends on what the inspection finds: a cap or top plate replacement is a short job, while relining a failed flue is a scheduled multi-part job. We give you a time estimate with the written quote once we know the scope. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
We service and install DuraFlex single-wall stainless relining kits, the Pro and ProFlex flexible stainless liner kits, insulated liner kits with wrap or insulation sleeve, and the Pro Rain Caps, Top Plates, and Multi-Flue Caps. In practice that’s the whole system – liner, insulation, and termination hardware. If you’re not sure what’s in your chimney, a Level 2 inspection tells you before anything gets scheduled.
Proper service does not void a warranty; careless service can. The usual culprits are aggressive sweeping that crimps or separates liner seams and a jagged bottom section left untrimmed. We trim clean, sweep to the liner’s tolerance, and fit terminations sized to the flue, all with the goal of leaving your installation warranty intact. If your warranty has specific conditions, tell us before we start and we’ll work around them.
A standard DuraFlex sweep in Irving typically runs in the range most chimney specialists charge for a single flue, and a Level 2 inspection – the camera work and photo report – is a separate line item quoted before we schedule. Repair and relining are priced per job by the written estimate, and we don’t recommend anything without camera evidence you can see for yourself. If work can safely wait, we tell you. Call (855) 955-5057 for an exact quote – estimates are free.
A DuraFlex-lined flue should be swept at least once a year and inspected annually, and more often if you burn heavily or through power outages. In Irving, where the fireplace often sits idle for months and then runs hard during an ice-storm outage, creosote builds in concentrated bursts – the yearly sweep is the floor, not a target. Call (855) 955-5057 to book an inspection before the next season.
In most cases a rusted top plate can be replaced without replacing the liner, provided the liner itself is still sound. The camera inspection is what tells us which side of that line you’re on. A homeowner with a DuraFlex relined flue often calls after noticing a rust streak on the firebox or a water stain on the ceiling near the chase, and a Level 2 camera inspection usually finds the top plate or cap gasket has degraded and water is running down alongside the liner. A qualified local pro typically pulls and reseals the top plate, replaces the cap with a correctly sized DuraFlex-compatible unit, and verifies the liner seams and insulation are still dry before sweeping. Call (855) 955-5057 and we’ll tell you plainly whether your liner can be saved.
Your cap needs to be sized to the flue opening and the liner’s outside diameter, and a cap that’s undersized or oversized lets rain and animals in or restricts the draft. Cap sizing is one of the most common reasons a DuraFlex installation fails at the top – the wrong cap means water runs down alongside the liner and soaks the insulation wrap, which is why we size it to the assembly rather than reaching for a one-size-fits-all cover. A Level 2 inspection tells you exactly what size your flue needs. Estimates are free at (855) 955-5057.
A standard poly brush used correctly won’t damage a sound DuraFlex liner, but a stiff or rotary head pushed hard can crimp corrugated stainless and open seams. The bottom transition matters too – an untrimmed jagged edge snags the brush and tears the liner with every pass. We match the brush to the liner, control the speed, and check the bottom cut before we start. If you want a durability assessment along with the sweep, call (855) 955-5057.
Sometimes, but it depends on the appliance and the liner – a gas appliance vented through an oversized, uninsulated single-wall DuraFlex liner is exactly the setup that produces upper-liner corrosion and pinholes from condensate. The liner often needs to be insulated or replaced with a correctly sized one. A Level 2 inspection and a careful look at the appliance before the conversion is the right sequence. Call (855) 955-5057 for an exact quote on inspecting your system.
Book Your DuraFlex Service in Irving, TX
Whether you need a sweep, a Level 2 inspection, cap replacement, or a repair to a rusted top plate, we’ll show you the camera evidence first and tell you when work can wait. We’re an independent DuraFlex service provider, not a manufacturer affiliate. Call (855) 955-5057 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Irving Chimney Cleaning.